Kongsberg M3 Sonar FLS Installation Manual Download | Manualshive

Page: 21 / 98

background image

922-20297011/1.0

19

– At least 2 meters (6.6 feet) from the path of radar beams. A typical radar beam spreads

20 degrees above and below the plane containing the radiating element.

• Protect the M3 Sonar FLS with a suitably rated fuse or circuit breaker. The power supply

should be adequately filtered to minimize equipment exposure to high-voltage transients
that may occur during engine start or when other high-power equipment is used on board
of the vessel.

• Ground the equipment in accordance to applicable electrical marine/vessel codes.

Note

Where the implementation of these recommendations is not possible, maintain the maximum
practical separation between system components and any other electrical/radio equipment
operation on the vessel.

Support information

If you need technical support for your M3 Sonar FLS you must contact your local dealer, or
our support department.

If you require maintenance or repair, contact your local dealer. You can contact us by phone
at +1 604 464 8144, or by email at:

[email protected]

. If you need

information about our other products, visit

http://www.km.kongsberg.com/mesotech

. On

our website you will also find a list of our dealers and distributors.

«
...
19
20
21
22
23
...
»

Summary of Contents for M3 Sonar FLS



































































































Reviews:

No comments

Related manuals for M3 Sonar FLS

Brand: Raymarine Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands