Komfovent 1300 U Installation Manual Download

Page: 35 / 36

UAB KOMFOVENT we reserve the right to make changes without prior notice

RHP STANDARD_21-04

You can stop the unit by pressing ON/OFF button in the “Overview” window.

8.3. Quick Inspection

The first time you start your device, make sure that:

Task

Yes

Comments

Control panel is working,

responds to touch, no error

messages

All air filters are installed

Air dampers fully open

There are no unusual noise or

vibrations

Changing the ventilation modes

changes the fan speed

The unit is airtight without gaps

or air leakage

Heating/cooling devices are

working

Connected external devices are

working

The condensate easily flows from

the unit and the drainage piping

is watertight

Check for leaks in the heat pump

piping system

Check if there is no mois-ture in

the refrigerant sys-tem

The heat pump compressor

operates properly, without any

extraneous noise and vibrations.

Other comments:

Installer

Company

Tel. No.

Date

Signature

Summary of Contents for 1300 U





































Search results

Summary of Contents for 1300 U

Reviews:

Related manuals for 1300 U

Brands by name

Popular brands

Komfovent 1300 U, Installation Manual

Search results

Summary of Contents for 1300 U

Reviews:

Related manuals for 1300 U

Brands by name

Popular brands