Kollmorgen AKI-CDC-MOD-15T Installation Manuals Download Page 3

Page: 3 / 36

AKI-CDC-MOD-15T | CONTENTS

1.1 About This Manual ....................................................................... 4

3 Installation

3.1 Space Requirements .................................................................... 8
3.2 Installation Process ...................................................................... 9

3.2.1 Connections to the Controller ................................................... 11
3.2.2 Other Connections and Peripherals ............................................ 11

4 Hardware Replacement

4.1 Replacing the Fan and Filter ............................................................. 12
4.2 Replacing the 2.5” SATA Mass Storage ................................................ 15
4.3 Replacing a CompactFlash or CFast Memory Card ................................... 17
4.4 Replacing the Battery .................................................................... 18

5 Technical Data
6 Chemical Resistance

6.1 Metal Casing ............................................................................. 21
6.2 Touch Screen and Overlay .............................................................. 22

6.2.1 Autotex F157/207 ................................................................ 22
6.2.2 Touch Screen Surface ........................................................... 22
6.2.3 TouchKeyboard and Screen Protection Film ................................... 23

7 Operator Panel Drawings

7.1 Connectors ............................................................................... 24
7.2 Communication Ports .................................................................... 24
7.3 AKI-CDC-MOD-15T Outline ............................................................ 25

8 Additional Installation Tips

Kollmorgen | October 2014

Summary of Contents for AKI-CDC-MOD-15T





































Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands

Kollmorgen AKI-CDC-MOD-15T, Installation Manuals

Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands