Kollmorgen AKI-CDC-MOD-15T Installation Manuals Download Page 2

Page: 2 / 36

Record of Document Revisions

Revision

Remarks

A, 07/2013

Preliminary edition

B, 10/2014

Updated UL information

Hardware Revision

Revision

Firmware revision

Software revision

Remarks

06/2013

2.0-SP1

Initial release

10/2014

b1.2.0.3

2.10

IMPORTANT NOTICE

Technical changes which improve the performance of the device may be made without prior notice!

Printed in the United States of America. This document is the intellectual property of Kollmorgen™. All rights reserved. No
part of this work may be reproduced in any form (by photocopying, micro

lm or any other method) or stored, processed,

copied or distributed by electronic means without the written permission of Kollmorgen™.

Kollmorgen | October 2014

Summary of Contents for AKI-CDC-MOD-15T





































Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands

Kollmorgen AKI-CDC-MOD-15T, Installation Manuals

Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands