Kollmorgen AKI-CDC-MOD-15T Installation Manuals Download Page 19

Page: 19 / 36

AKI-CDC-MOD-15T | TECHNICAL DATA

TECHNICAL DATA

Parameter

AKI-CDC-MOD-15T

Front panel,
W × H × D

410 × 286 × 83 mm

Cut out dimensions,
W × H

394 × 270 mm

Mounting depth

76 mm (176 mm including clearance)

Standalone
mounting

VESA 100 × 100
Note: Maximum screw length for VESA mounting is 5.5 mm. Usage of longer screws
may lead to damage.

Front panel seal

IP 65

Rear panel seal

IP 20

Touch screen
material

Polyester on glass, resistive.
Overlay: Autotex F157 or F207

(1)

Touch screen
operations

1 million

nger touch operations

Reverse side
material

Powder-coated aluminum

Frame material

Powder-coated aluminum

Weight

5.4 kg

Serial port for
COM1 RS232 and
COM2
RS422/RS485

9-pin D-sub contact with RS232 RTS/CTS, chassis-mounted female with standard
locking screws 4-40 UNC

Note:

RS422 Interface is not available yet.

Serial port for
COM3 RS232 and
COM4
RS422/RS485

9-pin D-sub contact with RS232 RTS/CTS, chassis-mounted female with standard
locking screws 4-40 UNC

Note:

RS422 Interface is not available yet.

Ethernet

2 × 10/100/1000 Base-T (shielded RJ45)

USB

4 × USB Host 2.0, max output current 500 mA

Processor

Intel® Celeron® B810E (2 × 1.6 GHz), 2 MB L2 Cache, Intel® QM67 Chipset

Optional:

Intel® Core™ i3 2310E (2 × 2.1 GHz) (Hyperthreading), 3 MB L2 Cache,

QM67 Chipset

Optional:

Intel® Core™ i7 2715QE (4 × 2.1 GHz) (Turbo 2.0, Hyperthreading),

6 MB L2 Cache, QM67 Chipset

External storage
media

via USB

Memory RAM

2 GB* / 4 GB* DDR-3 SO-DIMM 1333 MHz
*depending on Processor Module

LED

1 × multi-color

Real time clock

Yes (on chip)

Battery

Lithium battery type BR 2032 (or CR 2032), exchangeable

Power consumption
at rated voltage

114 W

Kollmorgen | October 2014

Summary of Contents for AKI-CDC-MOD-15T





































Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands

Kollmorgen AKI-CDC-MOD-15T, Installation Manuals

Search results

Summary of Contents for AKI-CDC-MOD-15T

Reviews:

Related manuals for AKI-CDC-MOD-15T

Brands by name

Popular brands