Kohzu Precision MontBlanc KOSMOS CRUX-D Page 19 User Manual Download

Page: 19 / 74

The zone sensor (DATUM) determines return direction and the edge of initial origin
sensor (ORG) becomes the origin position within the zone sensor.

Starting from CCW zone

①

Detection starts to CW direction with trapezoidal drive.

②

Decelerates and stops when zone sensor is detected.

③

Reverses to CCW direction and in low speed movement.

④

Reverses to CW direction after passing the zone sensor.

⑤

Stops at initial origin sensor detection after zone sensor

detection.

Starting from CW zone

①

'Detection starts to CCW direction with trapezoidal drive.

②

'Stops with deceleration after moving through zone sensor.

④

Reverses to CW direction in low speed movement.

⑤

Stops at initial origin sensor detection after zone sensor

detection.

The edge of zone sensor (DATUM) is the origin position.

Starting from CW zone

①

'Detection starts to CCW direction with trapezoidal drive.

②

'Stops with deceleration after moving through zone

sensor.

⑤

Reverses to CW direction in low speed movement.

⑥

Stops at the edge detection of zone sensor.

CCW

S3　領域センサ

CW域から開始

CCW域から開始

①

②

③

④

②’

⑤

⑥

①’

ドグ(検知板)

領域センサ

Starting from CCW zone

①

Detection starts to CW direction with trapezoidal drive.

②

Decelerates and stops when zone sensor is detected.

③

Reverses to CCW direction and in low speed movement.

④

Stops with deceleration after passing the zone sensor.

⑤

Reverses to CW direction in low speed movement.

⑥

Stops at the edge detection of zone sensor.

ドグ(検知板)

領域センサ

原点センサ

Dog (Detecting plate)

Zone sensor

Origin sensor

CCW

S1　原点(ORG)

S3　領域センサ

CW域から開始

CCW域から開始

①

②

③

④

②’

⑤

①’

Starting from CW zone

Starting from CCW zone

Origin(ORG)

Zone sensor

Starting from CW zone

Starting from CCW zone

Dog (Detecting plate)

Zone sensor

Summary of Contents for MontBlanc KOSMOS CRUX-D











































































Search results

Summary of Contents for MontBlanc KOSMOS CRUX-D

Reviews:

Related manuals for MontBlanc KOSMOS CRUX-D

Brands by name

Popular brands

Kohzu Precision MontBlanc KOSMOS CRUX-D, User Manual

Search results

Summary of Contents for MontBlanc KOSMOS CRUX-D

Reviews:

Related manuals for MontBlanc KOSMOS CRUX-D

Brands by name

Popular brands