Kohler Mira Evoco Dual Installation And User Manual Download Page 36 | Manualshive

Page: 36 / 48

background image

36

1478624-W2-A

Note: Waste trap not supplied.

Note: An installation tool is supplied, this is stowed within the assembled

waste body for packing purposes. Use this tool to screw the strainer into

the waste body.

Water Stopper

Installation Tool

Drain Assembly

Strainer

Waste

Body

Gasket

Gasket

a

b

c
e

g

f

h

d

a

b

c
e

g

f

h

d

Turn anti-clockwise to remove the water stopper then remove the installation tool,

then reassemble the water stopper to the waste body without the installation tool.

«
...
34
35
36
37
38
...
»

Summary of Contents for Mira Evoco Dual

















































Reviews:

No comments

Related manuals for Mira Evoco Dual

Brand: VADO Pages: 6

Brand: VADO Pages: 4

Brand: Maier Pages: 54

AXOR Starck 10411 Series

Brand: Hans Grohe Pages: 24

AXCES BOKX AX-BOK-149T-RRK-CP

Brand: VADO Pages: 10

Brand: Häfele Pages: 7

Brand: Hewi Pages: 36

Brand: Ancona Pages: 6

Brand: Kallista Pages: 12

Brand: Moen Pages: 4

Brand: iB Pages: 12

Brand: Patpet Pages: 13

Metris Select Prep 14848 1 Series

Brand: Hans Grohe Pages: 24

Metris S2 31160000

Brand: Hans Grohe Pages: 24

Metris Select 320 Eco 1jet 14785 Series

Brand: Hans Grohe Pages: 40

Talis Select S 300 72820000

Brand: Hans Grohe Pages: 40

Talis Select S Series

Brand: Hans Grohe Pages: 41

Tango C 04270 0 Series

Brand: Hans Grohe Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands