manualshive.com logo in svg

Kohler CURTIS 3401T, Manual

Share
Download
Kohler CURTIS 3401T Manual Download Page 48

 4 — PROGRAMMABLE PARAMETERS

Curtis Model 3401T – August 2022 

Return to TOC

pg. 42

PI Menu

The 3401T has a proportional/integral current controller, which is configured by the parameters on 

the PI menu.

PI MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Kp

0x66B0:00

1–100%

20–2048

16-bit

OEM Dealer

8%

Specifies the proportional gain factor of the current 

PI controller.

Ki

0x66C0:00

1–100%

20–2048

16-bit

OEM Dealer

20%

Specifies the integral gain factor of the current PI 

controller.

MISC MENU

The following table describes the parameters on the Misc menu.

MISC MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Mode Saving

0x4800:00

Off/On

0–1

32-bit

Field Intermediate

On

Specifies whether the speed mode is saved when 

the 3401T is powered down. On indicates that the 

speed mode is saved.

PIN Code Source

0x3102:00

Enumerated

0–2

32-bit

Field Intermediate

None

Specifies whether a password is required when the 

3401T is powered up and whether the 3401T or the 

ECS is used to enter the password:

0 = None. A password is not required.
1 = Internal. The 3401T is used.
2 =  External. The ECS is used. This value can be 

selected only when the 3401T and the ECS 

are in the operational NMT state and the 

ECS 

node ID is specified

.

HYD Controller Enable

0x6900:00

Off/On

0–1

32-bit

Field Intermediate

On

Specifies whether fault codes for the hydraulic 

controller are displayed. On = displayed.

Programmer Protocol

0x6902:00

Enumerated

0–1

32-bit

Field Intermediate

ESP/SP

Specifies the protocol used for Curtis  

programming devices:

0 =  ESP/SP. For the serial version of the 1313 

handheld programmer.

1 =  CIT. For the Curtis Integrated Toolkit™ (CIT) 

and the CANbus version of the 1313  

handheld programmer.

Vehicle Config

0x6909:00

1–65535

1–65535

32-bit

OEM Dealer

1

Specifies the type of vehicle that is being used with 

the 3401T. The correct value must be entered in 

order to 

view fault names

.

If you are not sure of the correct value, contact your 

Curtis distributor or the Curtis sales and support 

office in your region.

Summary of Contents for CURTIS 3401T































































Reviews:

No comments

Brands by name

Popular brands

Load more brands