Kohler CURTIS 3401T Manual Download Page 43

Page: 43 / 62

4 — PROGRAMMABLE PARAMETERS

pg. 37

Return to TOC

Curtis Model 3401T – August 2022

BDI MENU

The source of the BDI percentage can be either the 3401T’s internal BDI calculations or RPDO1. The

parameters on the BDI menu are used for the internal calculations.

BDI MENU

PARAMETER

CAN INDEX

VALUES

RAW VALUES

DATA SIZE

ACCESS LEVEL

DEFAULT VALUE

DESCRIPTION

Nominal Voltage

0x6400:00

Enumerated

0–2

32-bit

Field Intermediate

Specifies the battery’s nominal voltage:

0 = 12/48/80V
1 = 24/60/96V
2 = 36/72V

The BDI algorithm requires that the nominal voltage

is correctly specified.

Charge Full

0x6420:00

1.500–2.500V

1500–2500

32-bit

Field Intermediate

2.350V

Specifies the battery cell voltage above which the

battery is considered charged.
Charge Full must be at least 0.200V above

Charge Empty.

Charge Empty

0x6421:00

1.500–2.500V

1500–2500

32-bit

Field Intermediate

2.100V

Specifies the battery cell voltage above which the

battery is considered as starting to charge.
Charge Empty must be at least 0.200V below Charge

Full and at least 0.010V above Discharge Full.

Discharge Full

0x641E:00

1.500–2.500V

1500–2500

32-bit

Field Intermediate

2.040V

Specifies the battery cell voltage at which the state

of charge is considered 100%.
Discharge Full must be at least 0.120V more

than Discharge Empty and must be between the

following values:

• Charge Empty − 0.010V
• OCR Reset − 0.030V

Discharge Empty

0x641F:00

1.500–2.500V

1500–2500

32-bit

Field Intermediate

1.730V

Specifies the battery cell voltage at which the state

of charge is considered 0%.
Discharge Empty must be at least 0.120V less than

Discharge Full.

OCR Reset

0x6422:00

1.500–2.500V

1500–2500

32-bit

Field Intermediate

2.090V

Specifies the battery cell voltage above which the

BDI percentage is reset to 100%. OCR Reset is

checked only once; the check occurs when the

3401T is powered up.
OCR Reset must be at least 0.030V above Discharge

Full and at least 0.010V less than Charge Empty.

Integration Rate

0x6423:00

2–600 minutes

2–600

32-bit

Field Intermediate

30 minutes

Specifies the minimum time for the BDI algorithm to

decrease the BDI percentage from 100% to 0% or

increase the percentage from 0% to 100%.

Lift Lockout

0x6424:00

0.0–20.0%

0–200

32-bit

Field Intermediate

10.0%

Specifies the BDI percentage below which lift lockout

is activated.

Summary of Contents for CURTIS 3401T































































Search results

Summary of Contents for CURTIS 3401T

Reviews:

Brands by name

Popular brands

Kohler CURTIS 3401T, Manual

Search results

Summary of Contents for CURTIS 3401T

Reviews:

Brands by name

Popular brands