manualshive.com logo in svg

Kohler CURTIS 3401T, Manual

Share
Download
Kohler CURTIS 3401T Manual Download Page 16

 2 — USING THE 3401T

Curtis Model 3401T – August 2022 

Return to TOC

pg. 10

The following list describes the default passwords for accessing parameter menus:

•  User access level: 11111
•  OEM access level: 22222

Curtis recommends that you change the default passwords. Passwords are changed with the OEM 

Menu Password and USER Menu Password parameters on the 

Password menu

.

The following topics describe how to open and use the screens.

Open the 3401T’s Main Menu

Take the following steps to open the main menu.

1.  Go to the home screen.
2.  Press the 

 button. The main menu displays and you can now 

view and edit parameters

.

To exit the menu, press the 

 button.

Open the 3401T’s Parameter Menus

You must enter a password to open all of the 3401T’s menus, which include the main menu, Program 

menu, and Monitor menu. Take the following steps to open these menus.

1.  Go to the home screen.
2.  Press the   button. The Password screen displays:

1

2

3

4

5

>>>Enter 3401T Menu Password

OEM

The screen’s active access level is highlighted in blue; in the example above, the User access level 

is active.

Summary of Contents for CURTIS 3401T































































Reviews:

No comments

Brands by name

Popular brands

Load more brands