Koelstra BINQUE Daily, Instructions For Use Manual

Page: 26 / 32

MaMbo Daily
16
2. Remove the shoulder straps and belts with the Drings
from the back rest reinforcement plate.
3. Push the two fasteners at the bottom of the seat through
the openings in the upholstery so that they are no longer
visible.
4. Open the Velcro at the bottom of the upholstery and
remove the bottom reinforcement plate (see fig. 48).
The upholstery and the 5-point safety harness can now be
washed.
6.10 Installing the 5-point safety harness and upholstery
on the seat frame
Install the shoulder straps and belts with the Drings in the
back rest reinforcement plate:
1. Guide the shoulder straps underneath the back rest
adjustment strap (see fig. 47).
2. Push the shoulder straps on the side of the back rest
adjuster through the openings in the back rest
reinforcement plate at equal heights.
Attention: Check that the shoulder straps have not been
twisted.
3. Push the Drings through the back rest reinforcement
plate at the bottom.
To install the reinforcement plates:
1. Open the Velcro at the bottom of the upholstery.
2. Slide the bottom reinforcement plate with the fasteners
on the side of the slits into the upholstery (see fig. 48).
3. Check that the plastic fasteners protrude from the
designated openings in the upholstery (see fig. 46).
4. Close the Velcro.
5. Open the Velcro at the top of the upholstery and slide the
reinforcement plate with the back rest adjuster into the
opening at the back (top side)(see fig. 47).
6. Pull the Drings for the hip straps through the slits in the
seat at the front (bottom side) (see fig. 49).
7. Guide the shoulder straps through the slits in the
upholstery at the front (top side).
Attention: The shoulder straps must come out of the
back rest at the same height.
8. Check that the back rest adjuster protrudes from the
designated opening.
9. Guide the straps with the metal buckles through the
vertical slits at the back (top side) of the upholstery (see
fig. 50).
10. Close the Velcro at the top of the back rest.
To attach the upholstery to the seat frame:
1. Put the seat frame down on the ground in front of you
with the mounting points for the front brace facing up
(see fig. 51).
2. Place the upholstery in the middle, with the head end on
the side of the press studs on the seat frame and the
strap side facing up (see fig. 51).
3. Fasten the two press studs at the top of the upholstery to
the seat frame (see fig. 42).
4. Close the zip at the top of the upholstery around the seat
frame (see fig. 8).
5. Guide the straps with the metal buckles at the back
through the loop on the upholstery, each on one side,
then through the slit in the upholstery, then around the
frame tube and through the metal buckle (see fig. 43).
6. Close the zips and press studs on both sides.
To install the leg rest frame:
1. Squeeze the leg rest release and place the leg rest frame
with the leg rest release facing down between the
openings at the bottom of the seat (see fig. 52).
2. Pull the metal buckle of the crotch strap through the slit
at the bottom of the seat.
3. Fold the crotch strap around the leg rest frame and guide
the cover through the metal buckle (see fig. 46d).
4. Slide the leg rest frame into the compartment at the
bottom of the upholstery.
5. Check that the leg rest protrudes from the opening in the
upholstery (see fig. 46c).
6. Push the leg rest frame into the plastic fasteners of the
bottom reinforcement plate that protrude from the
upholstery (see fig. 46a).
To install the 5-point safety harness:
1. Thread the side of the hip strap without strap clip
through the Drings at the front of the seat.
2. Fasten the strap clip to the end of the hip strap, following
the example of the strap clip that is still attached.
3. Attach the shoulder straps to the hip straps
(see fig. 44).
4. Give all belts a gentle tug to check they are securely
attached.
5. Attach the safety front brace and if desired the canopy.