45
The operation of an overhead hoist involves more than activating the hoist’s controls. Per the ANSI/ASME B30
standards, the use of an overhead hoist is subject to certain hazards that cannot be mitigated by engineered features,
but only by the exercise of intelligence, care, common sense, and experience in anticipating the effects and results of
activating the hoist’s controls. Use this guidance in conjunction with other warnings, cautions, and notices in this manual
to govern the operation and use of your overhead hoist.
4.2
Shall’s and Shall Not’s for Operation
Improper operation of a hoist can create a potentially hazardous
situation which, if not avoided, could result in death or serious
injury, and substantial property damage. To avoid such a
potentially hazardous situation,
THE OPERATOR SHALL:
•
NOT
operate a damaged, malfunctioning or
unusually performing hoist.
•
NOT
operate a hoist until you have thoroughly read
and understood Manufacturer’s Operating and
Maintenance Instructions or Manuals.
•
Be familiar with operating controls, procedures, and
warnings.
•
NOT
operate a hoist that has been modified without
the manufacturer’s approval or without certification
that it is in conformity with ANSI/ASME B30
volumes.
•
NOT
lift more than rated load for the hoist.
•
NOT
use hoist with twisted, kinked, damaged, or
worn wire rope.
•
NOT
use the hoist to lift, support, or transport
people.
•
NOT
lift loads over people.
•
NOT
operate a hoist unless all persons are and
remain clear of the supported load.
•
NOT
operate unless load is centered under hoist.
•
NOT
attempt to lengthen the wire rope or repair
damaged wire rope.
•
Protect the hoist’s wire rope from weld splatter or
other damaging contaminants.
•
NOT
operate hoist when it is restricted from forming
a straight line from hook to support in the direction
of loading.
•
NOT
use hoist’s wire rope as a sling or wrap load
wire rope around load.
•
NOT
apply the load to the tip of the hook or to the
hook latch.
•
NOT
apply load unless the wire rope is properly
seated in its grooves.
•
NOT
apply load if bearing prevents equal loading
on all load-supporting wire ropes.
•
NOT
operate beyond the limits of the load wire
rope travel.
•
NOT
leave load supported by the hoist unattended
unless specific precautions have been taken.
•
NOT
allow the load wire rope or hook to be used as
an electrical or welding ground.
•
NOT
allow the load wire rope or hook to be touched
by a live welding electrode.
•
NOT
remove or obscure the warnings on the hoist.
•
NOT
operate a hoist on which the safety placards
or decals are missing or illegible
•
NOT
operate a hoist unless it has been securely
attached to a suitable support.
•
NOT
operate a hoist unless load slings or other
approved single attachments are properly sized,
and seated in the hook saddle.
•
NOT
use the hoist in such a way that could result in
shock or impact loads being applied to the hoist.
•
Take up slack carefully – make sure load is
balanced and load-holding action is secure before
continuing.
•
Shut down a hoist that malfunctions or performs
unusually and report such malfunction.
•
Make sure hoist limit switches function properly.
•
Warn personnel before lifting or moving a load.
•
Warn personnel of an approaching load.
Summary of Contents for Harrington RY Series
