Kingsman marquis ZCV39LPE2, Installation Instructions Manual

Page: 65 / 95

Proflame 1 -Remote Control Operation-
The Proflame GTM is configured to control the on/off main burner operation, its flame levels, and provides on/off and
Smart *thermostatic control of the appliance.
Transmitter
The Transmitter is powered by 3 AAA type batteries. A Mode
Key is provided to Index between the features and a
*thermostat Key is used to turn on/off or index through
*thermostat functions
Remote Receiver
The Receiver connects directly to the gas valve and stepper
motor with a wiring harness. The Receiver is powered by 4 AA
type batteries. The Receiver three position slider switch can be
set to one of three positions: ON (Manual Override), Remote
(Remote control) or Off.
Initializing the System for the first time
Install 4 AA batteries into the receiver battery bay. Install 3
AAA type batteries in the Transmitter battery bay.
Place the 3 position slider switch in the “Remote” position.
Insert the end of a paper clip into the hole marked “PRG” on
the Receiver front cover. The Receiver will “beep” three (3)
times to indicate that it is ready to synchronize with a
Transmitter. Push the On button. The Receiver will “beep” four
times to indicate the Transmitter’s command is accepted. The
system is now initialized.
Temperature indication Display
With the system in the “OFF” position, press the *thermostat
Key and the Mode Key at the same time. Look at the LCD
screen on the Transmitter to verify that a C or F is visible to the
right of the Room Temperature display.
Turn the Appliance On or Off
Press the ON/OFF Key on the Transmitter
Remote Flame Control
The Proflame GTM has six (6) flame levels. Pressing the Down
Arrow Key once will reduce the flame height by one step until
the flame is turned off. The Up Arrow Key will increase the
flame height each time it is pressed. If the Up Arrow Key is
pressed while the system is on but the flame is off, the flame
will come on in the high position.
Room *thermostat ( Transmitter Operation)
The Remote Control can operate as a room *thermostat. To
activate this function, press the *thermostat Key. The LCD
display on the Transmitter will change to show that the room
*thermostat is “ON” and the set temperature is now displayed.
To adjust the set temperature, press the Up or Down Arrow
Keys until the desired set temperature is displayed on the LCD
screen of the Transmitter.
Smart *thermostat (Transmitter Operation)
The Smart *thermostat function adjusts the flame height in
accordance to the difference between the set point
temperature and the actual room temperatures. As the room
temperature gets closer to the set point the Smart Function will
modulate the flame down. To activate this function, press the
*thermostat Key until the word "SMART" appears to the right of
the temperature bulb graphic. To adjust the set temperature,
press the Up or Down arrow Keys until the desired set point
temperature is displayed.
Key Lock Function
This function will lock the keys to avoid unsupervised
operation. To activate this function, press the MODE and the
UP Arrow Key at the same time. To de-activate this function,
press the MODE and the UP Arrow Key at the same time.
Low Battery Detection
Transmitter - When the Transmitter batteries are low, a
Battery Icon will appear on the LCD display of the Transmitter.
Receiver - When the Receiver batteries are low, No “beep” will
be emitted from the Receiver when it receives an On/Off
command from the Transmitter. When the batteries are
replaced the “beep” will be emitted from the Receiver when the
ON/OFF Key is pressed (See Initializing the System for the first
time).
Manual Bypass Of The Remote System
If the batteries of the Receiver or Transmitter are low or
depleted, the appliance can be turned on manually by sliding
the three position slider switch on the Receiver to the ON
position. This will bypass the remote control feature and the
appliance main burner will come on if the gas valve is in the
“On” position.
Remote Receiver
Transmitter
Wall Mount Option
10ft. Extension Harness (Part No. 1001-P904SI) required.
 The Remote Receiver can be mounted on a vertical
wall stud using the DCHS as a mounting bracket.
 Ensure that the face is protruding 1/2” so that the
face plate will be flush on the face of the wall.
 Drywall cutout size is 2” wide by 4-1/8” tall.

Must be installed within 10ft of valve assembly (6ft
recommended).
65