Kingsman Fireplaces MQZCVBG34LPE2 Installation Instructions Manual Download Page 26

Page: 26 / 80

MQZCVBG34

-Facing Requirements

Unit may be covered with combustible material (i.e. drywall) up to the fireplace opening.

MQZCVBG34

- Using Tile Lip

VALVE

IPI

SYSTEM

FIREPLACE CHASE MUST BE VENTED AT

THE TOP OF THE ENCLOSURE.

•

Minimum 90 square inches free air opening for

grills (V34EG & V34EGS).

• Minimum 2-1/8” Gap at top of enclosure for

Open Top chases.

Do not drive screws into

these highlighted areas.

Do not drive screws into

fireplace front. Facing

materials must be attached

to framing.

FRONT

A Tile Lip is supplied for attachment above the fireplace opening only.

This can be used as a standard tile edging or as a mount bracket for other

surfaces like drywall or plywood.
Set to desired height and attach through holes in face of fireplace.

For a complete Tile Lip Kit order ZBG34-TLK.

SIDE

Summary of Contents for MQZCVBG34LPE2

















































































Search results

Summary of Contents for MQZCVBG34LPE2

Reviews:

Related manuals for MQZCVBG34LPE2

Brands by name

Popular brands

Kingsman Fireplaces MQZCVBG34LPE2, Installation Instructions Manual

Search results

Summary of Contents for MQZCVBG34LPE2

Reviews:

Related manuals for MQZCVBG34LPE2

Brands by name

Popular brands