KidKraft F29655 Installation And Operating Instructions Manual Download

Page: 81 / 92

Fig. 35.1

Step 35: Monkey Ladder Assembly

Attach (858) Dowel to both posts with 2 (S2) Wood Screws. One screw is installed from top of the rails and the

other from the bottom as shown in fig. 35.3.

At bottom of (1367) Post MK attach (0353) MK Ground with 2 (H12) Hex Bolts (with lock washer, flat washer

and t-nut).

Be sure to keep the bolts loose.

(fig. 35.3)

Note: Pre-drill all holes using a 1/8” (3.2 mm) drill bit before installing the lag screws.
E:

Make sure the assembly is square and then attach 1 (0369) Lower Diagonal to each end of (0353) MK Ground

with 1 (H2) Hex Bolt (with lock washer, flat washer and t-nut) per diagonal, keeping the bolts loose, and to each

(1367) Post MK with 1 (LS2) Lag Screw (with flat washer) per diagonal. Once lag screws are installed tighten all

bolts from Steps D & E. (fig. 35.3)

Insert 1 (858) Dowel into 2 (1367) Post MK as shown in fig. 35.1.

Make sure shoulder of dowel is against each post before pre-drilling pilot

holes. Drill 1/8” (3.2 mm) pilot holes through the posts and into the dowel to

prevent splitting. (fig. 35.2)

Wood Parts

Hardware

2 x

Hex Bolt (lock washer, flat washer, t-nut)

2 x

Hex Bolt (lock washer, flat washer, t-nut)

2 x

Lag Screw (flat washer)

2 x

Wood Screw

2 x

Lower Diagonal

1 x

MK Ground

2 x

Post MK

1 x

Tennon Dowel

0369

0353

1367

858

LS2

0369

1367

0353

1367

858

1367

858

H12

0369

Fig. 35.2

Fig. 35.3

H12

LS2

FW1

LW1

TN1

FW1

Summary of Contents for F29655





























































































Search results

Summary of Contents for F29655

Reviews:

Related manuals for F29655

Brands by name

Popular brands

KidKraft F29655, Installation And Operating Instructions Manual

Search results

Summary of Contents for F29655

Reviews:

Related manuals for F29655

Brands by name

Popular brands