manualshive.com logo in svg

KidKraft F29655, Installation And Operating Instructions Manual, Page: 36 / 92

Share
Download
KidKraft F29655 Installation And Operating Instructions Manual Download Page 36

 36 

2 x 

Heavy SW Post

1 x 

SW Upright

1 x 

SW Support

Step 7:  Swing End Assembly

A:

  Loosely attach 2 (2613) Heavy SW Posts to (2615) SW Upright using 2 (G7) Hex Bolts (with lock washer, 

flat washer and t-nut).  Notice 2 bolt holes at top of (2615) SW Upright and orientation of angle.  (fig. 7.1)

B:

  Attach (2616) SW Support to both (2613) Heavy SW Posts and (2615) SW Upright using 3 (G4) Hex Bolts 

(with lock washer, flat washer and t-nut).  Tighten all bolts  (fig. 7.1)

C:

  Install 2 (WB7) Wafer Bolts (with flat washer and t-nut) in the top bolt holes in (2615) SW Upright as shown 

in fig. 7.1.  

IT IS IMPORTANT THAT THESE BOLTS ARE ATTACHED.  THEY WILL MINIMIZE CHECKING 

OF WOOD.

Hardware

Wood Parts

2 x 

Hex Bolt (lock washer, flat washer, t-nut)

3 x 

Hex Bolt (lock washer, flat washer, t-nut)

2 x 

Wafer Bolt (flat washer & t-nut)

G7

WB7

G4

Notice 2 bolt 

holes at top and 

orientation of 

the angle

WB7

Fig. 7.1

2613

2615

2613

2615

2616

G7

2616

G4

TN2

FW2

TN2

TN2

FW2

FW2

LW2

LW2

Summary of Contents for F29655





























































































Reviews:

No comments