manualshive.com logo in svg

KidKraft F29655, Installation And Operating Instructions Manual, Page: 64 / 92

Share
Download
KidKraft F29655 Installation And Operating Instructions Manual Download Page 64

 64 

Fig. 27.13

E:

  On the Back of the fort measure 21-5/8” (549 mm) from (2759) Roof End and 1-1/4” (32 mm) down from the top 

of (2677) Narrow Panel, pre-drill with a 3/16” (4.8 mm) drill bit then place 1 (2684) Mid Roof End centred over the 

pilot hole and flush to the top of (2677) Narrow Panel attach from the inside with 1 (S4) Wood Screw and from the 

outside with 1 (S3) Wood Screws. (fig. 27.12 and 27.13)

F:

  On the Front of the fort measure 21-5/8” (549 mm) from (2759) Roof End and 1-1/4” (32 mm) down from the top 

of the panel, pre-drill with a 3/16” (4.8 mm) drill bit then place 1 (2684) Mid Roof End centred over the pilot hole and 

flush to the top of the (2677) Narrow Panel and attach from the inside with 1 (S4) Wood Screw and from the outside 

with 1 (S3) Wood Screws. (fig. 27.12 and 27.14)

Step 27:  Attach Roof Ends 

Part 5

Flush

Flush

Back Wall

Fig. 27.14

2677

2759

2759

2759

Swing Wall

Fig. 27.12

2684

2684

2677

2677

2684

2759

Flush

Flush

Front Wall

Hardware

2 x 

Mid Roof End

Wood Parts

2684

2 x 

Wood Screw

2 x 

Wood Screw

S3

S4

S3

S3

S4

S4

2677

2684

21-5/8”

21-5/8”

Front 

Wall

Back 

Wall

End Wall

(549 mm)

(549 mm)

Summary of Contents for F29655





























































































Reviews:

No comments