KidKraft F29655 Installation And Operating Instructions Manual Download

Page: 26 / 92

Step 4: Frame Assembly

Part 1

It is important to assemble the frame on a flat, smooth surface.
A:

Place Swing Wall from Step 3 between 2 Front and Back Walls from Step 1, noticing the wall orientations.

The tops and bottoms of the walls should be flush. Make sure the walls are square then using the pilot holes as

a guide pre-drill with a 3/16” (4.8 mm) drill bit and fasten the Front Wall to the Swing Wall and Swing Wall to the

Back Wall with 4 (WL5) Wafer Lags per side. (fig. 4.1, 4.2 and 4.3)

Fig. 4.2

Fig. 4.1

Flush

Hardware

8 x

Wafer Lag

WL5

Flush

Notice Front

Wall overlaps

Swing Wall

WL5

Notice Swing Wall

overlaps Back Wall

Front Wall

Back Wall

Swing Wall

Back Wall

Swing Wall

Front Wall

Flush

Top View

WL5

Fig. 4.3

x 4 per

side

Notice grooves

face inwards

Notice counter sunk

holes on the outside

Summary of Contents for F29655





























































































Search results

Summary of Contents for F29655

Reviews:

Related manuals for F29655

Brands by name

Popular brands

KidKraft F29655, Installation And Operating Instructions Manual

Search results

Summary of Contents for F29655

Reviews:

Related manuals for F29655

Brands by name

Popular brands