KidKraft F29655 Installation And Operating Instructions Manual Download Page 49

Page: 49 / 92

Hardware

Step 18: Attach Cafe Canopy to Fort

8 x

Pan Screw (#8 flat washer)

2 x

Pan Screw

Fig. 18.2

Cafe Canopy

Frame

Fig. 18.1

Cafe Canopy

Other Parts

1 x Cafe Canopy Frame
1 x Cafe Canopy

Back Wall

Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 18.1)

With a helper hold the Canopy against the fort, on the End Wall as shown on the Jazz Fort Guide, measure

3-1/8” (79 mm) in from the outside edge of the (2770) End Post Left, making sure the Cafe Canopy is smooth and

tight then attach to the post with 2 (S5) Pan Screws (with #8 flat washer), measure 1-1/2” (38.1mm) down from the

first screw then attach a third screw and washer. Follow measurements as shown in fig. 18.2 for remaining screws

and washers. Measurements must be exact.

Hold the Cafe Canopy Frame against the panel and attach with 1 (S6) Pan Screw per side. (fig. 18.2)

FW3

2771

2770

Cafe Canopy

Frame

Cafe Canopy

x 1 per

side

x 8

Start on

this side

15”

5”

15”

3-1/8”

1-1/2”

79 mm

381 mm

127 mm

1-1/4”

38.1

31.8 mm

Summary of Contents for F29655





























































































Search results

Summary of Contents for F29655

Reviews:

KidKraft F29655, Installation And Operating Instructions Manual, Page: 49 / 92

Search results

Summary of Contents for F29655

Reviews: