KI ROGUE 2 Technical Manual Download | Manualshive

Page: 51 / 58

background image

50

Wheelbase Width Adjustment

Adjusting the wheelbase width allows the rider the option to move the wheels closer or further away from
the hips. It also compensates for camber adjustment and gives the proper wheel spacing to maximize
pushing efficiency.

To Adjust the Wheelbase Width

1. Remove the lower base mounts (B) by removing two bolts (A) per side using a 3mm Allen wrench. If

anti-tips are present, the image will look different, but the process is the same.

2.   Move the dimple clip (C) to the dimple on the camber plug (D) that provides the desired spacing.
3.   Repeat on opposite side.
4.   When both sides are spaced equally, tighten the bolts (A) to 70 in/lbs.

A

B

C

D

«
...
49
50
51
52
53
...
»

Summary of Contents for ROGUE 2



























































Reviews:

No comments

Related manuals for ROGUE 2

Brand: Z-Tec Pages: 4

Brand: Handicare Pages: 32

Zitzi Flipper Pro Flex

Brand: Anatomic SITT Pages: 24

Brand: Power Plus Mobility Pages: 11

Brand: Permobil Pages: 45

Brand: BCP Pages: 8

Brand: Mackworth Pages: 28

Brand: Permobil Pages: 52

Brand: Petermann Pages: 10

Brand: Handicare Pages: 40

Brand: HMN Pages: 16

Alante II GP202

Brand: Golden Pages: 40

Light Drive 2.1

Brand: BENOIT SYSTEMS Pages: 4

MULTI-MODE ACTIVATOR JS

Brand: Magic Mobility Pages: 10

Brand: Aquatec Pages: 2

Brand: Redman Power Chair Pages: 35

CHIEF 107 SERIES

Brand: Redman Power Chair Pages: 52

Brand: PowerStand Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands