KI ROGUE 2 Technical Manual Download | Manualshive

Page: 47 / 58

background image

46

Reversing Wheel Lock

5. Reinstall the wheel lock assembly onto the wheel lock bar. For a low profile scissor lock, use a 5mm

Allen wrench to install the two bolts. For the short throw and push to lock flush mount wheel locks,
install hardware using a 4mm Allen wrench and a 10mm wrench. For the push and pull to lock, slide the
assembly back onto the arbors. To install the spring on a push to lock, pull the curved spring arm over
the arbor shoulder. To install the spring on a pull to lock, pull the spring arm end into the wheel lock bar
hole (thin screwdriver will help with this). Place and tighten the top lock nuts to secure. See image
below.

NOTE: Always tighten wheel lock hardware by alternating between the two bolts while tightening a
little at a time. This prevents overclamping on one set of hardware which can lead to binding of the
fasteners and increased difficulty in removal.

6. Test the wheel locks. Ensure wheel lock arms embed in tires at least 1/8 inch when locked. If they do

not embed at least 1/8 inch, readjust wheel lock and test again.

Low Profile
Scissor Lock

Short Thro
Scissor Lock

Push to Lock Flush Mount
Wheel Lock

Push and Pull to Lock
Wheel Locks

«
...
45
46
47
48
49
...
»

Summary of Contents for ROGUE 2



























































Reviews:

No comments

Related manuals for ROGUE 2

Brand: Invacare Pages: 20

Brand: Invacare Pages: 3

Brand: Shoprider Pages: 24

Brand: Plusmed Pages: 2

Panacea DS-S18DDA-ELR

Brand: Direct Supply Pages: 2

Panacea DS-CX418ADDA-ELR

Brand: Direct Supply Pages: 2

Direct Choice Basic Cushions

Brand: Direct Supply Pages: 2

Brand: Royale Pages: 3

M2 Self propelled 310287

Brand: HMN Pages: 12

Brand: Dietz Pages: 2

Brand: Safer Locks Pages: 16

ICON BACK SYSTEM

Brand: VARILITE Pages: 12

Brand: Quickie Pages: 182

Everest & Jennings EJ87X-1

Brand: Graham Field Pages: 24

Brand: Permobil Pages: 32

Brand: R82 Pages: 8

XXL-Rehab Shower Commode Tilt

Brand: Cobi Rehab Pages: 12

Brand: Atlantis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands