KI ROGUE 2 Technical Manual Download Page 15

Page: 15 / 58

Index Towers and Camber Tube

5. When standard anti-tips are present - Install the anti-tip mount (D) onto the upper base mount with bolt

(C) and nut (E) using a 4mm Allen wrench and a 2.5mm wrench. Do not fully tighten until full camber
tube assembly is complete.

6. Install the anti-tip assembly (A) into the anti-tip sleeve (B). Install the anti-tip assembly and sleeve into

the anti-tip mount and ensure index button "clicks" and locks into one of the holes in the anti-tip
mount.

7. Install the camber tube (F) into the opening in the anti-tip mount.

8. When user activated anti-tips are present - Install the anti-tip spacer (C) and anti-tip assembly (B) onto

the upper base mount with bolt (A) and nut (D) using a 4mm Allen wrench and a 2.5mm wrench. Do not
fully tighten until full camber tube assembly is complete.

9. Install the camber tube (E) into the opening in the anti-tip mount.

Summary of Contents for ROGUE 2



























































Search results

Summary of Contents for ROGUE 2

Reviews:

Brands by name

Popular brands

KI ROGUE 2, Technical Manual

Search results

Summary of Contents for ROGUE 2

Reviews:

Brands by name

Popular brands