KI ROGUE 2 Technical Manual Download | Manualshive

Page: 8 / 58

background image

7

Caster Forks and Stems

3. If you are replacing your forks continue for instructions. For a regular caster fork, remove caster wheel

by removing two socket head screws and two spacers using two 4mm Allen wrenches. For a single
sided fork, remove the socket head screw, axle shaft and E-Clip using a 5mm Allen wrench.

Install Caster Fork and Stem

1. Install stem (A) into fork (B) with washer (E) and nut (F) using a 16mm wrench.
2. Install caster wheel (H) into fork (B) with two screws (C), a threaded barrel (D) and two spacers (G) using

two 4mm Allen wrenches.

NOTE: There is one size of caster stem (standard) and three sizes of forks (tall, standard and short)
that can be used. The image below shows the stem and forks. The installation process is the same
for whichever stem and fork you use.

3. Install assembly to caster housing by installing the two socket screws seen in step 2 on previous page.

Regular Caster Fork

Single Sided Caster Fork

A

B

C

C

D

E

F

G

G

H

Standard

Stem

Short

Fork

Standard

Fork

Tall

Fork

«
...
6
7
8
9
10
...
»

Summary of Contents for ROGUE 2



























































Reviews:

No comments

Related manuals for ROGUE 2

Quickie S-646 SE

Brand: Quickie Pages: 42

Brand: Feather Pages: 11

Brand: AAT Pages: 44

Brand: Küschall Pages: 136

Brand: Ti Lite Pages: 109

Brand: Permobil Pages: 20

Chairman Playman

Brand: Permobil Pages: 48

Brand: E-TRAVELLER Pages: 17

Brand: JBH Pages: 44

JOKER JUNIOR 2.0

Brand: progeo Pages: 26

Brand: Quickie Pages: 36

Brand: KYMCO Pages: 42

Q7 Active Rigid (welded)

Brand: Quickie Pages: 86

Brand: Golden Pages: 13

Brand: Quickie Pages: 94

Brand: Schuhmann Pages: 20

Brand: Leckey Pages: 25

Brand: Leckey Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands