Keysight U8001A User'S And Service Manual Download Page 77

Page: 77 / 81

Service Guide

Keysight U8001A/U8002A User’s and Service Guide

Current Calibration

For current calibration, connect an appropriate shunt 0.01

across the output

terminals, and connect a digital voltmeter (DVM) across the shunt resistor. Same

as voltage calibration, you will also be calibrating for low current, middle current

and high current calibration point respectively. Make sure that the power supply is

in constant current (CC) mode along the current calibration.

1 Current calibration mode

– Display will show “C” blinking.
– The CC annunciator will be turned on.
– Ensure that the power supply is in CC mode. Otherwise the CV annunciator

will fast-blink.

2 Low current calibration point.

– Display will show “C” blinking.
– The M1 annunciator will be turned on.
– Use the knob to enter the computed value (DVM reading divided by shunt

resistance).

– Press the “Memory” button to save the changes and move to the next

calibration point. You will be able to perform this if the power supply is in

CC mode.

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands