Keysight U8001A User'S And Service Manual Download Page 24

Page: 24 / 81

General Information

Keysight U8001A/U8002A User’s and Service Guide

Display Annunciators

Constant Current

OFF

Constant Voltage

Memory State 1

Memory State 2

Memory State 3

Over voltage Protection

Over current Protection

Limit

LOCK

Annunciators

Functions

Stores states of power supply in non-volatile memory.
When the power supply is in calibration mode, it can be used to store calibration constant.

OVP

The over voltage protection function is enabled when the annunciator turns on or the over voltage

protection circuit has caused the power supply to shutdown when the annunciator blinks.

OCP

The over current protection function is enabled when the annunciator turns on or the over current

protection circuit has caused the power supply to shutdown when the annunciator blinks.

LOCK

The front panel operation is disabled.

LIMIT

The display shows the limit values of voltage and current.

OFF

The output of the power supply is disabled.

The power supply is in constant voltage mode when the annunciator blinks.

The power supply is in constant current mode when the annuciator blinks.

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands