Keysight U8001A User'S And Service Manual Download Page 41

Page: 41 / 81

Operations and Features

Keysight U8001A/U8002A User’s and Service Guide

Programming Over Current Protection

Over current protection guards the load against output currents reaching values

greater than the programmed protection level.
The following steps show how to enable and disable the over current protection

(OCP), how to set the OCP trip level and how to clear the over voltage condition.

To set the OCP trip level and enable OCP

1 Press on the “Over Current” button.

– The LIMIT annunciator will be turned off.
– The OCP annunciator will fast-blink continuously.
– The display will show the OCP value and the character “A” will fast-blink

continuously.

2 Turn the knob to ad just the OCP value.

3 Press on the “Over Current” button again to end the adjustment and enable

the OCP.

– Display will show “donE”.
– The OCP annunciator will be turned on.

NOTE

To cancel the operation, allow the unit to idle for five seconds.

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands