Keysight U8001A User'S And Service Manual Download Page 52

Page: 52 / 81

Service Guide

Keysight U8001A/U8002A User’s and Service Guide

Replacement Parts

This section contains information for ordering replacement parts for your

instrument. The parts lists are divided into the following sections.
– Parts are listed in alphanumeric order according to their reference designators
– The parts lists include a brief description of each part with applicable Keysight

part number.

To order replaceable parts

You can order replaceable parts from Keysight using the Keysight part number.

Note that not all parts listed in this chapter are available as field–replaceable

parts. To order replaceable parts from Keysight, do the following:

Contact your nearest Keysight Sales Office or Service Center.

Identify the parts by the Keysight part number shown in the replaceable parts

list.

Provide the instrument model number and serial number.

Table 5-1

Replaceable parts

Part number

Description

2110-0014

Fuse 4.0 A T for 100 Vac and 115 Vac (U8001A)

2110-0006

Fuse 2.0 A T for 230 Vac (U8001A)

2110-0722

Fuse 6.25 A T for 100 Vac and 115 Vac (U8002A)

2110-1425

Fuse 2.8 A T for 230 Vac (U8002A)

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands