Keysight U8001A User'S And Service Manual Download Page 16

Page: 16 / 81

Quick Start

Keysight U8001A/U8002A User’s and Service Guide

Preliminary Checkout

The following steps help you to validate that the power supply is ready for use.

1 Check the list of supplied item.

Verify that you have received the following items together with your power

supply. If anything is found missing, contact your nearest Keysight

Technologies Sales Office.
– Power cord
– Certificate of Calibration
– Product Reference CD-ROM

2 Connect the power cord and turn on the power supply.

The front-panel display will light up while the power supply performs its power-on

self-test. The firmware revision is also displayed. If the power supply does not turn

on properly, see

page 19

NOTE

The power supply is shipped from the factory with a power- line cord that has a

plug approriate for your location. Your power supply is equipped with a 3- wire

grounding type power cord; the third conductor being the ground. The power

supply is grounded only when the power- line cord is plugged into an

appropriate receptacle. Do not operate your power supply without adequate

cabinet ground connection.

Summary of Contents for U8001A


















































































Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands

Keysight U8001A, User'S And Service Manual

Search results

Summary of Contents for U8001A

Reviews:

Related manuals for U8001A

Brands by name

Popular brands