Keysight N5241BU-205 Installation Note Download Page 28 | Manualshive

Page: 28 / 60

background image

28 Installation Note N5242-90125

Description of the Upgrade
Installation Procedure for the Upgrade

-

Step 15. Reinstall the Mixer Brick (MXB) Cables

Reconnect the other end of the mixer brick (MXB) cable (item

➀

) and all of the

IF multiplexer (IF MUX) gray cables (IF MUX board as shown (items

➁

through

➄

). Refer to

.

Figure 11

Reconnect the other end of the IF gray cables to the IF MUX board

«
...
26
27
28
29
30
...
»

Summary of Contents for N5241BU-205





























































Reviews:

No comments

Related manuals for N5241BU-205

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: Ocmis Irrigazione Pages: 100

Brand: Haaga Pages: 31

Brand: Nederman Pages: 89

Brand: Nederman Pages: 71

Brand: Nederman Pages: 131

Brand: X-Cite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands