Keysight N5241BU-205 Installation Note Download Page 54

Page: 54 / 60

54 Appendix - Synthesizer Board

Synthesizer Board Upgrade (N5240-60074 (with Tabs)/N5240-60076 (Without Tabs)

Version F/G to Version H)
Procedure

Procedure

If you have already removed your synthesizer board, proceed to step

Else, to remove your synthesizer board, refer to the Service Guide for your

instrument that can be downloaded from

www.keysight.com

Remove resistor R71. Refer to

Figure 1 on page 55

Clean pads.

Replace with resistor 1 k

(0699-3947). Refer to

Figure 1 on page 55

Remove capacitor C252.

Clean pads.

Table 1

Parts List for Synthesizer Board Upgrade Kit Modification

Part number

Description

0699-3947

1 k

Resistor

0161-4279

F capacitor

a. The factory will provide these items upon request.

Summary of Contents for N5241BU-205





























































Search results

Summary of Contents for N5241BU-205

Reviews:

Related manuals for N5241BU-205

Brands by name

Popular brands

Keysight N5241BU-205, Installation Note

Search results

Summary of Contents for N5241BU-205

Reviews:

Related manuals for N5241BU-205

Brands by name

Popular brands