Keysight N5241BU-205 Installation Note Download Page 33 | Manualshive

Page: 33 / 60

background image

Installation Note N5242-90125 33

Description of the Upgrade
Installation Procedure for the Upgrade

Step 18. Install A75 Low Frequency Extension (LFE) Board

1.

Install the LFE A75 board using the standoffs as a guide.

2.

Connect Motherboard / IF Multiplexer / LFT/ LFE/ Test set motherboard
(MB/IF MUX/LFT/LFE/TSMB) ribbon cable to LFE board J1 (item

➀

). Refer

to

3.

Install the A75 LFE board using the 0515-0665 screws x2. Torque to
9 in-lbs (item

➁

). Refer to

.

Figure 16

Install the A75 LFE board (N5240-60089, N5291-60005 and 0515-0665)

1

1. N5242B with Option 425 shown. N5241/2/9B with Option 205 is similar.

«
...
31
32
33
34
35
...
»

Summary of Contents for N5241BU-205





























































Reviews:

No comments

Related manuals for N5241BU-205

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Brand: Gardena Pages: 13

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: Quadro mdb Pages: 4

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Backyard Play Systems Pages: 52

Brand: Backyard Play Systems Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands