Keysight N5241BU-205 Installation Note Download Page 40 | Manualshive

Page: 40 / 60

background image

40 Installation Note N5242-90125

Description of the Upgrade
Installation Procedure for the Upgrade

-

Figure 21

Connect N5240-60097 and N5240-60098 from A71 and A74 Bias Tee

Combiners to A75 LFE Board (N5240-60097 (x1), N5240-60098 (x1),

1400-1391 (x2))

Step 21. Reinstall the A19 Test Set Motherboard

1.

For instructions, click the Chapter 7 bookmark “Removing and Replacing
the A19 Test Set Motherboard” in the PDF Service Guide

2.

Reconnect ribbon cable N5242-60006 from J213 to A24 mixer brick (2).

To see an image showing the location of the cable, click the Chapter 6

bookmark "Bottom Ribbon Cables and Wire Harnesses, Standard 2-Port
Configuration, Option 201" in the PDF Service Guide

1

.

1. See

“Downloading the Online PNA Service Guide” on page 7

«
...
38
39
40
41
42
...
»

Summary of Contents for N5241BU-205





























































Reviews:

No comments

Related manuals for N5241BU-205

Brand: UnionSpecial Pages: 56

Brand: GALLERY Pages: 18

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

Brand: DARAY Pages: 28

Brand: MacDon Pages: 88

Brand: Jiffy Pages: 15

Brand: B&K Pages: 12

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Laser Pages: 2

Brand: Lars Thrane Pages: 50

Brand: Rain-Flo Irrigation Pages: 16

Brand: Ganter Norm Pages: 20

Brand: Grundig Pages: 19

Brand: Megger Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands