manualshive.com logo in svg

Keysight N4431D, Reference Manual

Share
Download
Keysight N4431D Reference Manual Download Page 81

Electronic Calibration Modules Reference Guide                                                                               4-15

Use, Maintenance, and Care of the Devices
Gaging Connectors

Gaging Technique

1.

Connect and torque the device being measured to the gage. 

2.

Gently tap the barrel of the gage with your finger to settle the gage 

reading.

3.

Type-N and 7 mm: Read the gage indicator dial. If the needle has moved 

clockwise, the center conductor is 

protruding

 by an amount indicated by 

the black

 

numbers. If the needle has moved counterclockwise, the center 

conductor is 

recessed

 by an amount indicated by the red numbers. For 

more on 7 mm connectors, See also, 

“Gaging Technique–7 mm Gage” on 

page 4-16

.

1.85/2.4/2.92/3.5 mm: Read the gage indicator dial. Read only the black 

± signs; not the red ± signs.

4.

For maximum accuracy, measure the connector a minimum of three times 

and take an average of the readings. After each measurement, rotate the 

gage a quarter-turn to reduce measurement variations that result from the 

gage or the connector face not being exactly perpendicular to the center 

axis.

5.

Compare the average reading with the observed pin depth limits in the 

tables located in 

“Typical Pin Depth Values” on page 5-21

 for each type of 

connector.

Summary of Contents for N4431D















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands