Keysight N4431D Reference Manual Download Page 30

Page: 30 / 142

1-22 Electronic Calibration Modules Reference Guide

General Information
Compatible Network Analyzers

d. Compatible ENA E5071C instruments must have firmware version

≥

B.14.0x.

(ENA E5061B, E5063A, E5071C, and E5072A series analyzers are not

compatible with the N4693D and N4694D ECals.)

e. Compatible ENA E5063A instruments must have firmware version

≥

A.05.04.

(ENA E5061B, E5063A, E5071C, and E5072A series analyzers are not

compatible with the N4693D and N4694D ECals.)

f. Compatible ENA E5061B instruments must have firmware version

≥

B.05.00.

(ENA E5061B, E5063A, E5071C, and E5072A series analyzers are not

compatible with the N4693D and N4694D ECals.)

g. Compatible ENA E5080A instruments must have firmware version

≥

A.12.60.0x.

h. ENA E5080A instruments have no restrictions on firmware revision.

i. Compatible M9370/1/2/3/5A and M9485A PXIe instruments must have

firmware version

≥

A.12.60.0x.

N980xA PXIe instruments have no restrictions on firmware revisions.

j. Streamline Series USB-VNA instruments have no restrictions on firmware

revision.

k. Compatible FieldFox Handheld instruments must have firmware version

≥

A.10.2x (CPU2 units) and

≥

A.08.19 (CPU1 units).

l. The N9912A FieldFox does not support ECal.

Summary of Contents for N4431D















































































































































Search results

Summary of Contents for N4431D

Reviews:

Brands by name

Popular brands

Keysight N4431D, Reference Manual

Search results

Summary of Contents for N4431D

Reviews:

Brands by name

Popular brands