manualshive.com logo in svg

Keysight N4431D, Reference Manual

Share
Download
Keysight N4431D Reference Manual Download Page 26

 1-18                                                                                Electronic Calibration Modules Reference Guide

General Information
Compatible Network Analyzers

1-

b. Compatible PNA instruments must have firmware version 

≥

A.10.49.07.

c. Compatible ENA E5072A instruments must have firmware version 

≥

B.02.39.

d. Compatible ENA E5071C instruments must have firmware version 

≥

B.13.29.

e. Compatible ENA E5063A instruments must have firmware version 

≥

A.03.72.

f. Compatible ENA E5061B instruments must have firmware version 

≥

B.04.86.

g. Compatible ENA E5080A instruments must have firmware version 

≥

A.12.55.05.

h. ENA E5080B instuments have no restrictions on firmware revision.

i. Compatible PXIe instruments must have firmware version 

≥

A.03.10.

 

M980xA instruments have no firmware restrictions.

j. Compatible USB-VNA instruments must have firmware version 

≥

A.10.55.07

k. Compatible FieldFox Handheld instruments must have firmware version 

≥

A.10.2x (CPU2 units) and 

≥

A.08.19 (CPU1 units).

l. The N9912A FieldFox does not support ECal.

Summary of Contents for N4431D















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands