manualshive.com logo in svg

Keysight N4431D, Reference Manual

Share
Download
Keysight N4431D Reference Manual Download Page 27

Electronic Calibration Modules Reference Guide                                                                               1-19

General Information
Compatible Network Analyzers

Table 1-9 

N443xD Compatible Network Analyzers

Network

Analyzers

N4431D/32D ECal Module 

Series

N4433D ECal Module Series

Interface

Required 

a

PNA Network Analyzers

b,c

N5221/2/4/5/7A&B

Yes

Yes

USB

N5231/2/4/5/9A&B

Yes

Yes

USB

N5241/2/4/5/7/9A&B

Yes

Yes

USB

ENA Network Analyzers

E5072A

Yes

No

USB 

E5071C

Yes

No

USB 

E5063A

Yes

No

USB 

E5061B

Yes

No

USB 

E5080A

d

Yes

Yes

USB 

E5080B

e

Yes

Yes

USB 

PXIe Vector Network Analyzer Modules

f

M980xA, 

M9370/1/2/3/4/5A,

 

M9485A

Yes

Yes

USB

Streamline Series USB-VNA Vector Network Analyzer Modules

g

P500xA,P502xA
P9370/1/2/3/4/5A

Yes

Yes

USB

FieldFox Handheld Analyzers

h,i

N9923A

Yes

Yes

USB

N9913/4/5/6/7/8A/B

Yes

Yes

USB

N9925/6/7/8A

Yes

Yes

USB

N9950/1/2A

Yes

Yes

USB

a. N443xD supoorts any USB 2.0 compliant hub. It can communicate at High Speed (480 Mbps) and Full Speed 

(12 Mbps).

b. Compatible PNA A model instruments must have firmware version 

≥

A.10.60.04.

c. Compatible PNA B model instruments must have firmware version 

≥

A.12.85.00.

d. Compatible ENA E5080A instruments must have firmware version 

≥

A.12.55.05.

e. ENA E5080A instruments have no restrictions on firmware revision.

f. Compatible M937xA, M9485A PXIe instruments must have firmware version 

≥

A.10.55.07. 

 

M980xA instruments have no restrictions on firmware revision.

Summary of Contents for N4431D















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands