Keysight N4431D Reference Manual Download Page 100

Page: 100 / 142

5-10 Electronic Calibration Modules Reference Guide

Specifications and Characteristics
Characteristic Performance

Characteristic Performance

Characteristic performance for RF and microwave ECal modules are provided

in the following tables, which describe non-warranted performance that most

units exhibit.

N755xA Series

Table 5-17 Characteristic Performance for N755xA (3.5 mm)

a. When applied power exceeds –10 dBm, calibration results will be degraded from the performance indicated in this table.

Parameter

Frequency Range

DC to

500 MHz

to 4 GHz

4 to 6.5

GHz

6.5 to 9

GHz

9 to 14

GHz

14 to 18

GHz

18 to 26.5

GHz

Transmission Tracking (±dB)

b. Values based on using the network analyzer N5234A Option 200.

0.15

0.16

0.22

0.30

0.35

Load Match (dB)

Table 5-18 Characteristic Performance for N755xA (Type-N 50

)

a. When applied power exceeds –10 dBm, calibration results will be degraded from the performance indicated in this table.

Parameter

Frequency Range

DC to 500

MHz

500 MHz

to 4 GHz

4 to 6.5

GHz

6.5 to 9

GHz

9 to 14 GHz 14 to 18

GHz

Transmission Tracking (±dB)

b. Values based on using the network analyzer N5234A Option 200.

0.15

0.16

0.22

0.30

Load Match (dB)

Summary of Contents for N4431D















































































































































Search results

Summary of Contents for N4431D

Reviews:

Brands by name

Popular brands

Keysight N4431D, Reference Manual

Search results

Summary of Contents for N4431D

Reviews:

Brands by name

Popular brands