manualshive.com logo in svg

Keysight N4431D, Reference Manual

Share
Download
Keysight N4431D Reference Manual Download Page 135

Electronic Calibration Modules Reference Guide                                                                               6-5

Replaceable Parts
2.92 mm Modules and Accessories

2.92 mm Modules and Accessories

Table 6-4 2.92 mm Modules and Accessories

Description

a

a. See 

“Clarifying the Terminology of a Connector Interface” on page 1-1

.

Qty

Part Number

Adapters (added with Option 00A – N469xD only)

2.92 mm female to female adapter

 

2.92 mm male to male adapter

1

 

1

N4692-60022 

N4692-60021

Protective End Caps

2.92 mm -f -f connector cap (for module) 

b

 

2.92 mm -m-m connector cap (for module) 

b

 

2.92 mm -m -f connector cap (for module) 

b

 

2.92 mm female connector cap (for adapter) 

d

 

 

2.92 mm male connector cap (for adapter) 

d

 

b. Available on the N755xA ECals only.

1

 

1

 

1

 

as required

 

as required

N7550-40001

 

N7550-40003

 

N7550-40002

 

1401-0202

 

1401-0208

Gages 

d

2.92 mm female pin-depth gage 

c

 

2.92 mm male pin-depth gage 

c

c. A 3.5 mm gage is capable of measuring 3.5 mm and 2.92 mm connectors.

1

 

1

11752-60105

 

11752-60106

Other

Electronic calibration module reference manual (online)

 

USB cable, 2 meters

 

1/2 in to 9/16 in open-ended wrench 

d

20 mm, 90 N-cm (8 in-lb) torque wrench 

d

 

5/16 in, 90 N-cm (8 in-lb) torque wrench 

d

 

Spanner wrench 

d

 

Ruggedized plastic storage box for the ECal module and accessories (Option 
150) 

d

 

 

 

 

 

Replacement ruggedized plastic storage box for the ECal module and 
accessories 

e

 

d. These items are not included, but can be ordered separately.

e. This item is included, but a replacement can be ordered separately.

1

 

1

 

1

 

 

1

 

1

 

1

 

1

 

 

 

 

 

 

1

 

 

 

N7550-90002

 

8121-2671

 

8710-1770
8710-1764

 

8710-1765

 

08513-20014

 

 

N7550-60009 – 

Refer to 

Table 1-1, 

“N755xA 

Modules”, on 

page 1-6

.

 

1540-2345 – 

Refer to 

Table 1-4, 

“N469xD 

Modules”, on 

page 1-13

.

Summary of Contents for N4431D















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands