Keysight MIPI M-PHY User Manual Download Page 26

Page: 26 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

J-BERT M8040A MIPI

M-PHY Generator

With the M8040A it is possible to test two receiver channels of the DUT

simultaneously if you set

Channels

to 2. The Connection Diagram will

indicate the connections needed. Channel 1 is marked by yellow and

channel 2 by green.

If the instruments are online, i.e.,

Offline Connection

is set to OFF, you can

specify the connection of the software to the M8040A, that is, how it is

addressed.

Simple

is checked, type in the

Host IP address

and the

HiSLIP

, the

connection protocol over the IP address.

Advanced

is checked, specify the

Instrument address

using TCP/IP.

As described in the section

Frame Generator Setups

on page 10, a

BIT-3000 DSGA can be added to the setup. Set

Low speed analyzer

(DSGA)

to ON and specify the

DSGA address

. If the DUT has a reset and it

is to be used, set

DSGA Trigger

to ON.

Finally, there is the possibility to use results of level calibrations run in

ValiFrame.

Click

Connect

(see

Figure 5

) to finish configuring the setup.

BIT-3000 DSGA MIPI

M-PHY Generator

If the instruments are online, i.e.,

Offline Connection

is set to OFF, you can

specify the connection of the software to the BIT-3000. See

Figure 6

. The

Connection Diagram will indicate the connections needed.

Specify the

DSGA address

using TCP/IP.

Finally, click

Connect

to finish configuring the setup.

Summary of Contents for MIPI M-PHY













































































Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands

Keysight MIPI M-PHY, User Manual

Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands