Keysight MIPI M-PHY User Manual Download Page 53

Page: 53 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

Analysis Tab

Use the Analysis Tab to set parameters connected with the analysis of the

signal from the DUT. The parameter values can be entered numerically or

by using the slider that appears when you click the corresponding

parameter field. You can set the minimum, default or maximum level

quickly by clicking the buttons directly above the slider. If you click the

local

Apply

button in the bottom-right corner of the tab (see

Figure 21

the values will be applied to the instruments immediately.

Parameters in the Analysis Tab

•

Analysis Selector

Select either

Configuration

Analyzer

. First use

Configuration to configure the setup of the analyzer, then use Analyzer

to control the analyzer while it is running.

The parameters displayed also depend on whether the Low Speed

Analyzer (DSGA) is selected in the Connection window.

a) Configuration for Analysis without the Low Speed Analyzer (DSGA)

Ensure that the

Analysis Selector

is set to Configuration. If the Low

Speed Analyzer (DSGA) is not configured in the Connection window

(that is, it is set to OFF), you can set parameters for the BER Analyzer in

the Analysis Tab (see

Figure 21

NOTE

There is no analysis tab, i.e., it is disabled, if there is no DSGA in the

configuration and no M8046 module (BER analyzer) is connected.

Summary of Contents for MIPI M-PHY













































































Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands

Keysight MIPI M-PHY, User Manual

Search results

Summary of Contents for MIPI M-PHY

Reviews:

Related manuals for MIPI M-PHY

Brands by name

Popular brands