Keysight Technologies N5241B Installation Note Download Page 11

Page: 11 / 42

Installation Note N5242-90122 11

Description of the Upgrade
Items Included in the Upgrade Kit

W24

Port 2 CPLR THRU to A32 port 2 coupler

N5222-20053

W26

A32 port 2 coupler to front-panel Port 2 CPLR ARM

N5222-20034

W30

Front panel jumpers

N5222-20091

W38

REF 3 RCVR R3 IN to A24 mixer brick (R3)

N5242-20270

W39

REF 4 RCVR R4 IN to A24 mixer brick (R4)

N5242-20271

W42

A21 HMA26.5 to A22 splitter

N5222-20009

W43

A22 splitter to A23 mixer brick

N5222-20007

W44

A22 splitter to A24 mixer brick

N5222-20008

W52

A23 mixer brick (R1) to A20 IF multiplexer (P411)

N5242-60021

W53

A23 mixer brick (R2) to A20 IF multiplexer (P412)

N5242-60022

W55

A24 mixer brick (D) to A20 IF multiplexer (P801)

N5242-60024

W56

A24 mixer brick (R4) to A20 IF multiplexer (P414)

N5242-60019

W57

A24 mixer brick (R3) to A20 IF multiplexer (P413)

N5242-60020

W58

A24 mixer brick (C) to A20 IF multiplexer (P601)

N5242-60023

W60

A20 IF multiplexer (P203) to A12 SPAM (J2)

N5242-60013

W62

A20 IF multiplexer (P603) to A12 SPAM (J5)

N5242-60015

W67

A10 frequency reference board J7 to A13 13.5 GHz source 2 synth board J5

N5242-60030

W75

A26 port 3 bridge to A35 port 3 source attenuator

N5222-20002

W76

A35 port 3 source attenuator to front-panel Port 3 SOURCE OUT

N5222-20019

W79

A27 port 4 bridge to A36 port 4 source attenuator

N5222-20001

W80

A36 port 4 source attenuator to front-panel Port 4 SOURCE OUT

N5222-20020

W89

Port 3 RCVR C IN to A43 port 3 receiver attenuator

N5222-20021

W90

A43 port 3 receiver attenuator to A24 mixer brick (C)

N5242-20306

W91

Port 4 RCVR D IN to A44 port 4 receiver attenuator

N5222-20022

W92

A44 port 4 receiver attenuator to A24 mixer brick (D)

N5242-20307

Ribbon cable, A19 test set motherboard J202 to A35 port 3 source attenuator

N5242-60008

Ribbon cable, A19 test set motherboard J203 to A36 port 4 source attenuator

Ribbon cable, A19 test set motherboard J206 to A43 port 3 receiver attenuator

8121-0982

Ribbon cable, A19 test set motherboard J207 to A44 port 4 receiver attenuator

Table 1

Contents of Upgrade Kit N5242-60122

Ref

Desig.

Description

Qty

Part Number

Summary of Contents for N5241B











































Search results

Summary of Contents for N5241B

Reviews:

Related manuals for N5241B

Brands by name

Popular brands

Keysight Technologies N5241B, Installation Note

Search results

Summary of Contents for N5241B

Reviews:

Related manuals for N5241B

Brands by name

Popular brands