Keysight Technologies N5241B Installation Note Download Page 27 | Manualshive

Page: 27 / 42

background image

Installation Note N5242-90122 27

Description of the Upgrade
Installation Procedure for the Upgrade

Install the Second Source Boards into the Analyzer

Refer to

for this part of this step of the procedure. New parts are

listed in

Table 1 on page 9

1.

Install the A8 26.5 GHz source 2 board (5087-7837) and the A13 13.5 GHz

source 2 synthesizer board (N5240-60074) in the analyzer as shown.
Secure the A8 26.5 GHz source 2 board with two screws (item

①

;

0515-0380) and torque to 21 in-lbs.

2.

Connect cable W2 (N5222-20090) between the A8 26.5 GHz source 2

board and the A13 13.5 GHz source 2 synthesizer board as shown. Be sure

to position the cable in the wire looms as shown. Tighten the cable

connectors to 10 in-lbs using a 5/16-in torque wrench.

3.

Connect the loose end of gray flex cable W67 (N5242-60030) to the A10

frequency reference board (J7). (The other end of this cable was previously

connected to J5 of the source 2 synthesizer board.)

«
...
25
26
27
28
29
...
»

Summary of Contents for N5241B











































Reviews:

No comments

Related manuals for N5241B

Brand: Keithley Pages: 55

Brand: Gas Data Pages: 99

Frontline 802.11

Brand: Teledyne Lecroy Pages: 223

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Brand: DAKOTA ULTRASONICS Pages: 51

Brand: RADWAG Pages: 12

Brand: Alcor System Pages: 21

Brand: Doepke Pages: 2

Brand: Simpson Pages: 28

Brand: ENSONIQ Pages: 260

Brand: mru Pages: 32

Pure Resonator BB

Brand: K&K Sound Pages: 4

Brand: Agilent Technologies Pages: 79

Brand: WPI Pages: 32

Commeter AR006274

Brand: GUILCOR Pages: 14

Brand: Lowrey Pages: 61

N4906B Serial BERT

Brand: Agilent Technologies Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands