Keysight Technologies N5221BU-605 Installation Note Download Page 78

Page: 78 / 88

78 Installation Note N5222-90114

Installation Procedure for the Upgrade

To store the backup data, perform these steps:

— Navigate to the EEPROM Backup Utility, located at:

—

Windows 7 --

C:\Program Files (x86)\Keysight\Network

Analyzer\Service\eebackup.exe

— Windows 10 --

C:\Program Files\Keysight\Network

Analyzer\Service\eebackup.exe

— Run the program.
— Click Backup EEPROM.
— Click Backup TSMB Mem.
— Click Exit when the program has finished.

Operator’s Check

Perform the Operator’s Check to check the basic functionality of the analyzer.

For instructions, click the Chapter 3 bookmark “Tests and Adjustments” in the
PDF Service Guide

f you experience difficulty with the basic functioning of the analyzer, contact

Keysight. Refer to

“Contacting Keysight” on page 4

Calibration

Although the analyzer functions, its performance relative to its specifications

has not been verified. It is recommended that a full instrument calibration be

performed using the analyzer’s internal performance test software. To view

information on the performance test software, click the Chapter 3 bookmark
“Tests and Adjustments” in the PDF Service Guide

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands