Keysight Technologies N5221BU-605 Installation Note Download Page 22

Page: 22 / 88

22 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 9. Remove Some Low Frequency Extension (LFE) Cables

(8120-5014 (x1), 8120-5021 (x1), N5240-60097 (x1), and

N5240-60098 (x1)) From the IF Multiplexer (IF MUX) Board

Disconnect the other end of the 8120-5014 (x1) and 8120-5021 (x1) cables on
the IF MUX board (items



and



). You disconnected the other ends of the IF

gray cables previously in the process in

“Step 7. Disconnect A71 and A74

Bias-Tee Combiner’s LFE Cables From the A70 Low Frequency Extension (LFE)

Board and the Ends of the LFE Cables Connected to the IF Multiplier (IF MUX)

Board” on page 20

). Refer to

Figure 3

— Save 8120-5014 cable for reuse.
— Discard 8120-5021 cable.

Figure 3

Disconnecting the gray cables on the IF MUX board (8120-5014 (x1) and

8120-5021 (x1))

IMPORTANT!

Before disconnecting the IF gray cables, be careful to label

where the cables connect on the IF multiplexer (IF MUX) board. Not all

cables are reused and some will move to new positions. See also,

Figure

on page 51

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands