Keysight Technologies N5221BU-605 Installation Note Download Page 51

Page: 51 / 88

Installation Note N5222-90114 51

Installation Procedure for the Upgrade

Step 33. Reconnect/Connect Old and New Cables and then Route

Low Frequency Extension (LFE) Cables (8120-5014 (x2) and

8120-5017 (x3)) and the Other Ends of the Cables Connected to the IF

Multiplexer (IF MUX) Board

Reconnect and route 8120-5014 (x2), 8120-5017 (x3). Connect and route
the cables on the IF MUX board as shown (items



through



). You will

connect the other ends of the IF gray cables later on the process. Refer to

Figure 29

Connecting and routing the gray cables on the IF MUX board (8120-5014 (x2)

and 8120-5017 (x3))

The 8120-5014 (x1) cable connection that was connected at P604 is now

connected on P404. The new 8120-5017 cable is used for the P604

connection on the IF multiplexer (IF MUX) board. Refer to

Figure 29

When connecting the IF gray cables, be careful to look for the correct

connector labels on the IF multiplexer (IF MUX) board.

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands