Keysight Technologies N5221BU-605 Installation Note Download Page 65

Page: 65 / 88

Installation Note N5222-90114 65

Installation Procedure for the Upgrade

Connect New N5240-60098 (x1) Port 3 and Verify N5240-60098 Port 1

Blue Bias-Tee Combiner Cables and Clamps from the A71 and A72 Bias

Tees “RF-IN” to the A70 LFE Board “Port1” and “Port3” Connectors and

Install Clamps onto the Ferrite Beads

Install the N5240-60098 (x2) cable as shown. Note the orientation of the
cable (item



through



Route cables as shown.

Figure 38

Connect new N5240-60098 (x1) from Port 3 and verify N5240-60098 from

Port 1 Bias Tee Combiners to A70 LFE Board and install Clamps onto the

Ferrite Beads (N5240-60098 (x2), and 1400-1391 (x1)).

Verify Port

1 cable is

properly

routed and

secured.

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands