Keysight Technologies N5221BU-605 Installation Note Download Page 4

Page: 4 / 88

4 Installation Note N5222-90114

Getting Assistance from Keysight

Installing this upgrade kit requires special skills and experience. If you think

you may not be qualified to do the work, or need advice, contact Keysight.

Contacting Keysight

Assistance with test and measurements needs and information on finding a

local Keysight office are available on the Web at:

http://www.keysight.com/find/assist

If you do not have access to the Internet, please contact your Keysight field
engineer.

If You Have Problems With the Upgrade Kit Contents

Keysight stands behind the quality of the upgrade kit contents. If you have

problems with any item in the kit, refer to

www.keysight.com

and the

Contact

Keysight

(

) link.

In any correspondence or telephone conversation, refer to the Keysight

product by its model number and full serial number. With this information,

the Keysight representative can determine whether your product is still

within its warranty period.

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands