Keysight Technologies N2797A User Manual Download Page 42

Page: 42 / 48

N2797A User’s Guide

Performance Verification

Figure 17

PV Fixture Connected to VNA

Perform a Calibration for the

PORT 1

side of the Reference plane.

Press the

reflection

screen key.

Connect the open end of 85052D Calibration Standard to the non-pincher side of the

PV/DS test board.

Select the

open

screen key under the

Forward

group.

Wait until the VNA beeps indicating that it has completed the task.

Connect short end of Calibration Standard to the non-pincher side of the PV/DS test

board.

Select

short

screen key under the

Forward

group.

Wait until the VNA beeps indicating that it has completed the task.

Connect load end of Calibration Standard to the non-pincher side of the PV/DS test

board.

Select the

loads

screen key under the

Forward

group.

Press

broadband

screen key selection.

Wait until the VNA beeps indicating that it has completed the task.

Press the

done loads

screen key.

You have just calibrated one side of the reference plane.

Connect the other high quality SMA cable to the VNA’s

PORT 2

as shown in

Figure 18

Summary of Contents for N2797A

















































Search results

Summary of Contents for N2797A

Reviews:

Related manuals for N2797A

Brands by name

Popular brands

Keysight Technologies N2797A, User Manual

Search results

Summary of Contents for N2797A

Reviews:

Related manuals for N2797A

Brands by name

Popular brands