Keysight Technologies N2797A User Manual Download Page 33 | Manualshive

Page: 33 / 48

background image

Characteristics and Specifications

3

N2797A User’s Guide

33

This symbol indicates the Environmental Protection Use Period (EPUP) for the

product’s toxic substances for the China RoHS requirements.

The CE mark is a registered trademark of the European Community. ISM GRP 1-A

denotes the instrument is an Industrial Scientific and Medical Group 1 Class A

product. ICES/NMB-001 indicates product compliance with the Canadian

Interference-Causing Equipment Standard.

WEEE Compliance

This product complies with the WEEE Directive (2002/96/EC) marking

requirements. The affixed label indicates that you must not discard this

electrical/electronic product in domestic household waste.

Product Category: With reference to the equipment types in the WEEE

Directive Annex I, this product is classed as a "Monitoring and Control

Instrumentation" product. Do not dispose in domestic household. To

return unwanted products, contact your local Keysight office, or refer to

www.keysight.com for more information.

Dimensions

«
...
31
32
33
34
35
...
»

Summary of Contents for N2797A

















































Reviews:

No comments

Related manuals for N2797A

Brand: B meters Pages: 18

Brand: B meters Pages: 14

Brand: WAGNER Pages: 9

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brand: Hach Pages: 96

Brand: Topcon Pages: 62

Brand: RHS Pages: 8

International 2S Pro

Brand: Brantz Pages: 2

Brand: Salutron Pages: 2

Brand: Lasertec Pages: 28

Brand: Hach Pages: 2

Brand: Velleman Pages: 18

Brand: Skil Pages: 80

Brand: Labgear Pages: 2

Beta 10P Series

Brand: ST Pages: 32

Brand: Medical International Research Pages: 46

Brand: sewerin Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands