KLP031308
3-11
• If
E241
(hardware error) is showing in the status display, check the master and/or slave
setup. If necessary, use
FUNCTION
switch to enter the M/S menu to change the config-
uration as described above.
• If there is no communication between units for approximately 10 seconds, all units will
turn off their output and the status display will flash
E241
(hardware error), then
xOFy
where
x
= unit number and
y
= total number of units, and finally the serial/parallel config-
uration setting
SERI
or
PARA
.
3.2.12
LAN INTERFACE CONFIGURATION [-1.2K MODELS ONLY]
Using a thin tool (e.g. end of paper clip), press
FUNCTION
switch once until status display
reads
VIRT
, then rotate either
VOLTAGE
or
CURRENT
control until status display reads
LAN
.
Press
DC OUTPUT
switch to enter the LAN Interface configuration menu. Rotate either
VOLT-
AGE
or
CURRENT
control to see the available functions.
•
LRST
- LAN Reset. To restore the LAN interface configuration to the factory default,
rotate either
VOLTAGE
or
CURRENT
control to show
YES
in the
DC VOLTS
display,
then press
DC OUTPUT
switch. The factory default settings are listed in PAR. 3.3.1.3.
•
DHCP
- DHCP status is displayed in the
DC VOLTS
display. To change the setting press
DC OUTPUT
switch, then rotate either
VOLTAGE
or
CURRENT
control to see desired
setting and press
DC OUTPUT
switch to save.
•
ON - The KLP requests an IP address from the DHCP server. (AUTOIP set to
OFF.)
•
OFF - The KLP uses the IP, MASK, GATE and DNS addresses established by
the user using either the UTIL - LAN menus at the front panel, the web interface
(see PAR. 3.3.6) or via SCPI commands over one of the digital interfaces.
(AUTO IP also set to OFF.)
• AUTO
- AUTO IP status is displayed in the
DC VOLTS
display.
•
ON - The KLP obtains an IP address automatically. (Both DHCP and AUTO IP
set to ON.)
•
OFF - The KLP uses the IP, MASK, GATE and DNS addresses established by
the user using either the UTIL - LAN menus at the front panel or via SCPI com-
mands. (AUTOIP set to OFF.)
• MAC1
- Shows first pair of hex digits of the MAC address (e.g., for MAC address 01-23-
45-67-89-AB the
DC VOLTS
display shows
01
- and the
DC AMPERES
display shows
23-
). Cannot be changed by the user.
• MAC2
- Shows second of two hex digits of the MAC address (e.g., for MAC address 01-
23-45-67-89-AB the
DC VOLTS
display shows
45
- and the
DC AMPERES
display
shows
67-
). Cannot be changed by the user.
• MAC3
- Shows third pair of hex digits of the MAC address (e.g., for MAC address 01-23-
45-67-89-AB the
DC VOLTS
display shows
89-
and the
DC AMPERES
display shows
AB
). Cannot be changed by the user.
•
IP1
- Shows first half of IP address (e.g., for IP address 192.168.000.200 the
DC
VOLTS
display shows
192._
and the
DC AMPERES
display shows
168._
). To change
Summary of Contents for KLP 10-150-1.2K
